The main purpose
1. Uses: It is suitable for heat transfer printing equipment, large-scale mechanical equipment sealing and other industries. It can be used as heat-resistant baking gaskets for electronic instruments and circuit boards, heat-resistant pads for textile dyeing machines, food baking placemats, automobiles, aerospace, Computers, mechanical and electronic industries, fax machines, high-temperature parts in printers; automotive mechanical bodies, kitchen appliances, home appliances and other equipment, etc.
2. Features: Silicone foamed silicone rubber has excellent heat resistance, cold resistance, dielectric properties, ozone resistance and atmospheric aging resistance. The outstanding performance of silicone rubber is that it can be used at -60°C (or lower temperature) to +250°C (or higher temperature) for long-term use. However, the mechanical properties of silicone rubber such as tensile strength and tear resistance are poor, and its physical and mechanical properties are not as good as most synthetic rubbers at room temperature. It is an amorphous substance, highly active adsorption material, insoluble in any solvent, non-toxic, tasteless, stable in chemical properties, and does not react with any substance except strong alkali and hydrofluoric acid.
3. Advantages: 1. Anti-ultraviolet, anti-ozone, extreme temperature resistance and flame retardancy 2. Strong sealing ability, which can effectively prevent tiny particles and rain. 3. Sealing, dust-proof, moisture-proof, air-tight and light-shielding, vibration isolation, fire prevention 4. Vibration isolation used in electronic equipment and vehicle interiors 5. Cushion pads and gaskets
4. Performance parameters of foamed silica gel board:
1. Environmental performance Water absorption internal: 1.40% at room temperature for 24 hours Complies with FDA CFR 177.2600 Part C requirements for food contact ingredients HT-800 gray and black 2. Electrical and thermal properties Dielectric constant, ASTM D 150 1.4
2. Dielectric strength, ASTM D 149, Volts/mil 91 dry arc resistance, ASTM D 495, second 92 volume resistivity, Ohm-cm ASTM D 257 1014 thermal conductivity, BTU in/hr/ft2/ºF (w/ mºk) ASTM C 518 0.63 (0.09)
3. Temperature resistance at -67ºF (-55ºC) low-temperature flex ASTM D 1056 passed recommended operating temperature ºF (ºC) SAE J-2236 -67 to 392 (-55 to 220) recommended maximum temperature for intermittent use, ºF ( ºC) Internal 482 (250)® HT-800
4. Typical value of AOKE performance test method Physical properties Color gray red black white brown orange
Thickness: (mm) Tolerance 0.8mm-60mm±0.1
Standard width, (mm) 500-1500
Density, (g/cm³) ASTM D 1056 0.35-0.9
Pressure Deflection, psi (kPa) Force measured at 25% deflection ASTM D 1056
Compression Set, % Max ASTM D 1056 Test D<1 at 158ºF (70ºC) ASTM D 1056 Test D <5 at 212ºF (100ºC) Tensile Strength, psi (kPa) ASTM D 412 45 (310) Elongation , % ASTM D 412 80 flame retardancy and outgassing
Flame Retardancy UL94 V-0 and HF-1 Class Flame Spread Index (Ls) ASTM E 162<25 Smoke Density (Ds) ASTM E 662 Tested in 4.0 minutes <50 Tested in 1.5 minutes <20 Toxic Gas Emission Rating SMP-800CPASS
5 sheet size 500mm*500mm 500mm*1000mm, thickness 1mm-50mm
Please check the details about foamed silicone:
https://www.siliconefoam.net/product-high-elastic-foam-silicone-strip-iota-4801-.html
